Key facts
- A steel coil quotation is built from the specification: substrate, size, grade, coating or paint, slitting, coil weight, packing, quantity and delivery term.
- The EN 10346 coating designation is the nominal total coating mass of both surfaces in g/m², so it belongs in every enquiry.
- Slit coil is cut from a master coil, so it is a different offer from full-width coil.
- Incoterms rules set which tasks, costs and risks sit with the seller, and they do not set the amount payable, the currency or the credit terms.
- Two quotations compare fairly only when every field of the specification matches.
What goes into the cost of a steel coil order?
Behind any coil quotation sit many separate technical items, which a single headline figure would hide. Reinwent publishes no prices, so this guide lists the items, and every supplier can then be asked to quote against the same list. They are the substrate and the process route, the size, the grade, the coating or paint system, any slitting, coil weight and packing, quantity, surface finish, and the delivery term with freight and payment. The table sorts them by what to state.
| Driver | Why it matters | What to state |
|---|---|---|
| Substrate | Hot rolled, cold rolled, galvanized, Aluzinc and prepainted coil follow different process routes | Coil type and condition |
| Thickness and width | Each coil type has its own range, and tolerance classes differ | Nominal size in mm, tolerance class |
| Grade and standard | The designation sets the properties delivered | One named standard and grade |
| Coating or paint | Coating mass and paint layers change what is applied to the strip | Designation in g/m² [oz/ft²], paint system, colour |
| Slitting | An extra step on the master coil | Slit widths, tolerance, edge needs |
| Coil weight, packing | Affects handling and container fit | Inner diameter, maximum weight, packing |
| Quantity | Set per size, grade and width plan | Tonnes per item |
| Destination | Decides freight, delivery term and timing | One Incoterms rule, named port |
How do substrate, size and grade enter the quote?
The five coil types sourced here run through different lines. Hot rolled coil is supplied pickled and oiled, cold rolled coil as Full Hard or annealed, and galvanized, Aluzinc and prepainted coil carry a coating on a cold rolled base; see hot rolled vs cold rolled coil. A coated coil therefore carries the work of the base plus the coating line, and a prepainted coil adds a paint line on top.
Size matters because the ranges differ: hot rolled runs from 0.80 to 5.00 mm (0.031 to 0.197 in) [0.031 to 0.197 in], cold rolled from 0.20 to 3.00 mm (0.008 to 0.118 in) [0.008 to 0.118 in], and full width reaches 600 to 1650 mm (23.62 to 64.96 in) [23.6 to 65.0 in] depending on the coil type. A size at the edge of a range is a different request from one in the middle, and the exact limit is confirmed at quotation. Dimensional standards allow normal or special tolerances; EN 10131 delivers with normal tolerances unless the order says otherwise, so tolerance class is a line to state. Thickness and width selection explains how to choose both.
Grade is the third part of the substrate. Name one standard and one designation, because DX51D+Z and S350GD+Z are different goods; the grades guide explains the names.
What do coating mass and paint system add?
IspatGuru lists the mass or thickness of the metal coating among the factors in choosing a coated product, and notes that coating weight is controlled on the line by air or nitrogen knives. For EN 10346 the designation, for example Z275 or AZ150, is the nominal total mass of both surfaces in g/m² [1.00 oz/ft² is 305 g/m² in ASTM usage]. A coil quoted as Z100 and one quoted as Z275 are not the same offer. The galvanized vs Aluzinc guide compares the two coatings, and the finish and spangle guide covers the surface options that also belong in the enquiry.
Prepainted coil adds layers. Wikipedia describes a coil coating line that cleans and pretreats the strip, applies a primer and a finish coat, each cured, and recoats the underside with a backing coat that is generally not as thick as an exterior finish. So the paint system, the colour and the top and back coats all belong in the request; see paint systems and RAL colours. The maximum coil weight of prepainted coil on our page is 15 t [33,100 lb], against 30 t [66,100 lb] for most of the others.
Why does slitting change the offer?
Wikipedia calls roll slitting a shearing operation that cuts a large roll into narrower rolls, and says burrs on slit edges are commonplace and that precise tension control is the key to good slitting. It also says very narrow, thin strips become unstable. So slit coil is a separate offer from full-width coil: the master coil is processed, narrower strips weigh less per coil, and edge and camber requirements may be tighter. Slit widths on our pages start at 20 mm (0.787 in) [0.8 in]. State the widths, the tolerance and what the edge must do; see slit coil vs full-width coil.
How do coil weight, packing and quantity matter?
Heavier coils and different packing change how the cargo is handled and how it sits in a container. Payload limits differ between carriers, so the number of containers an order needs is set by coil weight, packing and the container type; the packing and container loading guide collects the figures. For a fixed outer and inner diameter the coil weight follows the width, and the weight calculator returns strip mass and length. Quantity is set per quotation and depends on the size, the grade and the width plan, so give tonnes per item, not one total for a mixed order.
What does the delivery term change?
The International Chamber of Commerce publishes eleven Incoterms rules, which clarify the tasks, costs and risks of delivering goods from seller to buyer. Wikipedia stresses what they leave out: they do not determine the amount payable, the currency or the credit terms. An EXW quotation leaves transport, insurance and export clearance to you, a CIF quotation adds freight and insurance to the named port, and a DDP quotation covers the most. They are different offers even for the same coil. Whether duties or customs apply depends on the destination, so confirm the classification with your broker. Ask each offer which rule, which port, and which payment terms and currency apply.
How do you compare two quotations technically?
Put both on one sheet and mark every line where they differ. Typical differences are the standard or grade, the tolerance class, the coating mass or paint system, slit versus full width, coil weight and packing, the quantity and the delivery term. A gap between two offers is explained by those lines, not by the coil alone. The related guides below list every field and walk through the order steps.
What should you tell the trader?
Send the table above filled in, with the destination and the Incoterms rule. Reinwent is a trading and sourcing company that sources coil from manufacturers in Türkiye, so the same specification goes to several mills, the offers come back on one basis and you keep one point of contact until delivery. We publish no prices; we put offers on one basis, so you compare like with like. Send the details through the quote request form and the quotation comes within 12 hours at the latest. The five coil types are on the steel coil page: galvanized, cold rolled, pickled hot rolled, prepainted and Aluzinc.
Related coil guides: steel coil HS codes; importing steel coil from Türkiye; steel coil importers guide; steel coil manufacturers in Türkiye.
Read next: steel coil FAQ, steel coil: Türkiye vs China, what is cold rolled steel, what is hot rolled steel.

Steel



