Zn-Al (Galfan-type) coated wire
Zn-Al (Galfan-type) coated wire is low carbon steel wire with a zinc-aluminium coating, in diameters from 1.2 to 5.5 mm (0.047 to 0.217 in) with a coating mass of 40 to 350 g/m². Standard: EN 10244-2. Origin: Türkiye, other qualified mills on request.
Last updated

- Origin
- Türkiye, other qualified mills on request
Specifications
| Property | Value |
|---|---|
| Diameter | 1.20–5.50 mm (0.047–0.217 in) |
| Zinc coating | 40–350 g/m² |
| Tensile strength | 350–900 N/mm² |
| Raw material | Low carbon steel wire |
| Coil weight | 250–1000 kg |
| Standards | EN 10244-2 |
Uses
- Base wire for further drawing, wrapping and forming
- Wire that is zinc-aluminium coated for outdoor corrosion protection
- Coated low carbon steel wire in a chosen tensile band
Zn-Al (Galfan-type) coated wire: what it is
Zn-Al coated wire is low carbon steel wire covered with an alloy of zinc and aluminium. The coating is usually called Galfan-type: zinc with about 5 % aluminium and a small addition of mischmetal. Galfan is a registered trademark, so this page writes Zn-Al (Galfan-type) for the coating in general. The wire offered here comes in diameters from 1.2 to 5.5 mm (0.047 to 0.217 in), with a coating mass from 40 to 350 g/m², and follows EN 10244-2. These are ranges, confirmed in the quotation.
How it differs from galvanized wire
Galvanized wire carries a plain zinc coating. Zn-Al coated wire keeps the zinc but changes the alloy, so the coating adds aluminium to the zinc. For what the aluminium changes, which standard applies and what the references say about corrosion, read our guide on Galfan (Zn-5Al) wire vs galvanized wire. For plain zinc, see galvanized wire.
Specification ranges
The specification table above gives the ranges. Diameters run from 1.2 to 5.5 mm (0.047 to 0.217 in), coating mass from 40 to 350 g/m² and coil weight from 250 to 1,000 kg. Tensile strength comes in three bands: 350 to 500 N/mm², 500 to 700 N/mm² and 700 to 900 N/mm². Coating mass is the mass of coating per square metre of wire surface; the figure you need depends on the diameter, the standard and the environment, so state it in your request.
Where Zn-Al coated wire is used
Buyers use it as base wire for further drawing, wrapping and forming, and where the wire has to resist corrosion outdoors and a zinc-aluminium coating is specified. The tensile band is chosen to suit the job: a lower band for wire that is formed or wrapped, a higher band for wire that must carry load.
For a plain zinc coating, see galvanized wire; for higher tensile strength without coating, cold drawn wire. For customs, see steel wire HS codes. We source this wire from manufacturers in Türkiye; Reinwent is a supplier and trading company. To order, request a quote and name Zn-Al coated wire in the request.
Questions buyers ask
What is Zn-Al coated wire?
It is low carbon steel wire whose coating is an alloy of zinc and aluminium instead of plain zinc. The coating of this type is usually called Galfan-type: zinc with about 5 % aluminium and a little mischmetal. The wire offered here is a range of low carbon steel wire with this coating, and the quotation confirms the exact coating for your order.
How does Zn-Al coated wire differ from galvanized wire?
Galvanized wire carries a plain zinc coating, while Zn-Al coated wire carries zinc alloyed with aluminium, so the two are named and specified separately. Our guide on Galfan (Zn-5Al) wire vs galvanized wire sets out what the aluminium changes and what the references support.
Which standard applies to Zn-Al coated wire?
EN 10244-2 covers the coating mass, other properties and testing of zinc and zinc-alloy coatings on steel wire. Name the standard in your request and confirm the class in the quotation.
What should a request for Zn-Al coated wire contain?
Send one diameter in millimetres, the coating mass in g/m² or the class, the standard, the tensile band, the coil weight, the quantity, the delivery term and a named port through the quote form on this site.
What diameters and coating masses are available?
Diameters run from 1.2 mm to 5.5 mm (0.047 to 0.217 in) and the coating mass from 40 to 350 g/m². These are ranges, confirmed in the quotation for your diameter and coating mass.
What coil weights does Zn-Al coated wire come in?
Coil weights run from 250 to 1,000 kg. This is a range, confirmed in the quotation together with the packing.
What tensile strength does Zn-Al coated wire have?
Tensile strength is offered in three bands: 350 to 500 N/mm², 500 to 700 N/mm² and 700 to 900 N/mm². The bands are a range, confirmed in the quotation, so state the band you need.
How does Reinwent handle an order for Zn-Al coated wire?
Reinwent is a trading and sourcing company that supplies steel wire. The Zn-Al coated wire is sourced from manufacturers in Türkiye, and other qualified mills on request. Send the specification through the quote form and you receive a quotation within 12 hours at the latest.
Buying for the United States? Read about steel wire sourcing for the US market: inch diameters, wire gauge, pounds and ASTM standards.

Steel
