Galfan (Zn-5Al) wire vs galvanized wire

Galfan wire is steel wire coated with zinc alloyed with about 5 % aluminium (Zn-5Al) instead of plain zinc. The alloy forms a thin bond layer on the steel, and an industry note reports at least twice the outdoor corrosion resistance of galvanize on sheet of the same coating weight. EN 10244-2 covers zinc and zinc-alloy coatings on steel wire.

Last updated

Key facts

  • Galfan-type coating is zinc with about 5 % aluminium plus a little rare-earth mischmetal; the generic name is zinc-5% aluminium (Zn-5Al).
  • Galfan is a registered trademark; this guide uses Zn-5Al for the coating in general.
  • Zn-5Al is a eutectic alloy, and its bond layer on the steel is thinner than the layer on galvanized steel.
  • The zinc industry reports at least twice the outdoor corrosion resistance of galvanize of the same coating weight, measured on sheet.
  • EN 10244-2 covers zinc and zinc-alloy coatings on steel wire.

What is Zn-5Al (Galfan-type) wire?

It is steel wire whose coating is an alloy of zinc with about 5 % aluminium and a small addition of rare-earth mischmetal (cerium and lanthanum). The International Zinc Association (IZA) technical note on the coating says the mischmetal improves wetting and coating ductility and helps against intergranular corrosion, and that ASTM B750 specifies the alloy composition. Galfan is a registered trademark; the generic name is zinc-5% aluminium, written Zn-5Al.

Ordinary galvanized wire carries a plain zinc coating. Zn-5Al wire keeps the zinc but changes the alloy.

How does Zn-5Al differ from zinc?

Zinc with 5 % aluminium is a eutectic composition, which means the metal freezes at one temperature into very thin, alternating plates. The IZA note also states that the alloy layer between coating and steel is very thin, thinner than the layer on galvanized steel, and gives that as the reason for the coatingโ€™s formability. For wire, which is drawn and wrapped, that is the practical point: the coating is meant to follow the steel when the wire is formed. Aluminium adds barrier protection, while the zinc keeps protecting cut ends by corroding first.

Does Zn-5Al last longer than galvanize?

The IZA note reports field studies showing at least twice the outdoor corrosion resistance of conventional galvanize of the same coating weight, in rural, industrial and marine air. It describes the loss of Zn-5Al as slowing over time, against a steadier loss for galvanize. Two cautions apply. The studies were made on coated sheet, and the note is a general guide, not a promise for any wire order. How a given wire performs depends on the environment, the diameter and the coating mass.

The note frames the choice as one of value: specify the same coating weight as galvanize for a longer life, or about half the galvanize weight for a similar life. For wire, agree the coating mass with the mill and do not assume sheet results carry over one to one. For how plain zinc coatings compare, read hot-dip vs electro-galvanized wire.

Galvanized wire vs Zn-5Al wire compared

Galvanized wire compared with Zn-5Al (Galfan-type) wire
FeatureGalvanized (zinc)Zn-5Al (Galfan-type)
Coating metalZincZinc with about 5 % aluminium and a little mischmetal
ProtectionBarrier and sacrificialBarrier (aluminium) and sacrificial (zinc)
Bond layer on the steelZinc-iron alloy layersA very thin layer, thinner than on galvanized steel
Why it forms wellDepends on the coating and the processThe thin bond layer, according to the IZA note
StandardsEN 10244-2, ASTM A641EN 10244-2; ASTM B750 for the alloy composition

The table lists only what the cited references support. It gives no coating-mass figures, because the required mass depends on the standard, class and diameter; see zinc coating classes.

Which standard applies?

EN 10244-2 covers the coating mass, other properties and testing of zinc and zinc-alloy coatings on steel wire. ASTM B750 gives the composition of the Zn-5Al-mischmetal alloy. ASTM B802, B803 and B958 are for Zn-5Al-coated core wire of overhead conductors, and A1007 is for rope wire; none of them is a general-purpose wire standard. Name the standard in your request and ask the mill to confirm the class in the quotation.

What should a request for Zn-5Al wire include?

  • One diameter in mm.
  • The standard: EN 10244-2 or an ASTM specification.
  • The coating mass or class.
  • The tensile band.
  • The coil weight and the quantity.
  • The delivery term and a named port.

Buying from abroad? See galvanized wire from Tรผrkiye and galvanized wire from Tรผrkiye vs China for what to compare on one specification.

Reinwent sources steel wire from manufacturers in Tรผrkiye. The range of diameters and coatings depends on the mill and is confirmed in the quotation, so request a quote and name Zn-5Al in the request. You receive a quotation within 12 hours at the latest.

Questions buyers ask

Is Galfan a type of galvanized wire?

Loosely, yes: both are zinc-based coatings on steel wire. Strictly, galvanized wire carries a plain zinc coating and Galfan-type wire carries zinc with about 5 % aluminium, so the two are named and specified separately.

Is Galfan better than galvanized wire?

For outdoor corrosion resistance on sheet, the zinc industry's technical note reports at least twice the performance of galvanize of the same coating weight. That is a general guide, not a promise for a given wire order. Environment, diameter and coating mass all matter.

Is Zn-5Al the same as Galvalume or Aluzinc?

No. Zn-5Al is mostly zinc with about 5 % aluminium. Galvalume and Aluzinc are 55 % aluminium-zinc coatings with different behaviour. The coil guide on [galvanized vs Aluzinc coil](/steel/guides/galvanized-vs-aluzinc-coil/) explains that coating.

Which standard applies to Zn-5Al wire?

EN 10244-2 covers zinc and zinc-alloy coatings on steel wire, and its zinc-aluminium coatings are the ones that apply here. ASTM B750 gives the composition of the alloy itself. Name the standard in your request and confirm the class in the quotation.

What do I put in a request for Zn-5Al wire?

One diameter in mm, the standard (EN 10244-2 or an ASTM specification), the coating mass or class, the tensile band, the coil weight, the quantity, the delivery term and a named port.

Can I halve the coating mass and get the same life?

The zinc industry note describes that choice for sheet: the same coating weight for a longer life, or about half the galvanize weight for a similar life. Treat it as a general guide and agree the coating mass for wire with the mill.

Are ASTM B802, B803 and B958 the right standards for general wire?

No. Those ASTM specifications cover Zn-5Al-coated steel core wire for overhead conductors, and A1007 covers rope wire. They are not general-purpose wire standards.

Does Reinwent supply Zn-5Al wire?

Reinwent sources steel wire from manufacturers in Tรผrkiye. Ask for Zn-5Al wire in the quote form: the diameters and coating range depend on the mill and the quotation confirms them. You receive a quotation within 12 hours at the latest.

Sources

Request a quote

Tell us the specification you need and we will check it with manufacturers in Tรผrkiye. We reply with a quotation within 12 hours.

Request a quote