Steel coil manufacturers in Türkiye: how to pick

Evaluate a steel coil manufacturer in Türkiye by the processing lines it runs and by how it answers a precise specification: standard, grade, thickness, width, coating, packing. Pickling, cold rolling, galvanizing, painting and slitting are separate lines, and few plants run all of them. Reinwent is a trading and sourcing company that sources coil from manufacturers in Türkiye and names no mills.

Last updated

Key facts

  • Türkiye is one of the ten largest crude steel producers in the world, according to worldsteel’s top 10 table.
  • Pickling, cold rolling, annealing, hot-dip coating, coil coating and slitting are separate processing lines, and a plant may run only some of them.
  • Pickled and oiled hot rolled coil is the usual feedstock for cold rolled coil, and cold rolled coil is the usual base for galvanized coil, which in turn is the base for prepainted coil.
  • A mill is judged by what it states in writing against your specification, not by how it describes itself.
  • Reinwent is a trading and sourcing company that sources coil from manufacturers in Türkiye. It publishes no mill names.

What should a buyer look for in a coil mill?

A mill’s description of itself does not tell you whether your coil will arrive as specified. What does tell you is how the mill answers a precise request: whether it names the standard and grade, states the size limits it can roll, names the coating designation and puts coil weight, inner diameter and packing in writing.

This guide does not list companies. Reinwent does not publish supplier names, and the mill that suits a galvanized order may not be the one that suits a cold rolled order. The questions below let you test any offer, whoever sends it.

Which lines does a coil mill run?

Coil is made in stages, and each stage is a separate line. The product pages show where each coil type sits.

The processing line behind each coil type and what to ask about it
Coil typeLine behind itStandards we supply toAsk the mill
Pickled and oiled hot rolledPickling line, then oilingEN 10111, EN 10025-2, EN 10149-2Grade, thickness, width, oil film
Cold rolledCold rolling, annealing, temper rollingEN 10130Full Hard or annealed, grade, surface
GalvanizedContinuous hot-dip zinc coating lineEN 10346, ASTM A653/A653MCoating designation, grade, finish
AluzincContinuous hot-dip aluminium-zinc coating lineEN 10346, ASTM A792AZ designation, thickness, width
PrepaintedCoil coating line on a galvanized baseEN 10169, EN 10346Paint system, colour, base coating

On a pickling line the coil passes through acid, and hydrochloric acid is the main acid used in steelmaking. This removes the oxide scale left by hot rolling, and a thin oil film protects the clean surface. Cold rolling then reduces the pickled strip to a finished thickness, and annealing and a light temper rolling pass give the formable grades. The hot rolled versus cold rolled guide explains these steps, and the annealing and surface quality guide goes further into the cold rolled condition.

In continuous hot-dip galvanizing the strip runs through a bath of molten zinc on a coating line, and the Aluzinc line does the same with an aluminium-zinc alloy of about 55% aluminium. The galvanized versus Aluzinc guide compares the two coatings. Coil coating is a continuous, highly automated process for painting metal coils, and the usual base is hot-dip galvanized steel. The paint systems guide covers the paint choices.

Because the lines are separate, one plant may run all of them, and another may run only some and take its base coil from elsewhere. That is not a fault in itself, but it matters for your order, so ask.

How do you check a mill’s claims on size, coating and strength?

Turn every claim into a figure the offer must carry.

Standard and grade. Ask which standard and grade designation the mill will supply. The standards guide shows what each designation means, and the grades guide reads the letters and numbers. Which grades are available depends on the mill.

Thickness and width. Ask for the nominal thickness and width in millimetres, with the tolerance class. The thickness and width guide explains normal and special tolerances. Each coil type has its own limits, and a mill that rolls 0.20 mm (0.008 in) [0.008 in] cold rolled strip may not run the same range on its coating line.

Coating. Ask for the coating designation and the coating mass counted on both sides together, from the standard you named. For galvanized coil, ask which surface finish the mill supplies; the spangle and surface finish guide explains the choice.

Coil weight and diameters. Ask for the inner diameter, the maximum coil weight and the outer diameter the mill can pack. The weight calculator shows what a given width and outer diameter produce.

If a mill answers only in general words, the offer is not finished. Send it back with the missing fields marked. EN 10021, the general technical delivery conditions for steel products, lists the items a purchaser may specify when ordering, so it is a useful checklist of what your enquiry can state.

What about slitting and packing?

Slitting is a separate operation: a slitting line cuts wide coil lengthwise into narrower coils. A mill may do it on its own line or pass the coil to a service centre, so ask who slits the coil and who is responsible for the width tolerance and edge condition. The slit versus full-width guide sets out when each is the better choice.

Packing decides whether the coil arrives clean and undamaged. Ask how the coil is wrapped, strapped and labelled, how it is oriented in the container and what the mill does for oiled or painted surfaces. The packing and container loading guide explains the usual practice.

Is Türkiye a sensible place to look?

worldsteel’s table of the top ten crude steel producers lists Türkiye, and the Turkish Steel Exporters’ Association describes the country as one of the largest steel producers and exporters. Coil is rolled, coated and painted from that steel base, so a buyer deals with an established steel industry.

We stop there. This guide gives no coil volumes or rankings, because neutral published figures for coil on its own are hard to confirm. Whether a given mill can meet your size, grade, coating and packing is a question for each order, not for statistics.

What does a trading and sourcing company add?

Reinwent is a trading and sourcing company that sources coil from manufacturers in Türkiye. You send one specification, and we ask suitable manufacturers to quote against it, set the offers on one basis so you compare like with like, and follow the order through the production slot, packing, loading and shipping. The steps are set out in the guide to importing steel coil from Türkiye, and the importers guide gives the buyer checklist.

Send the specification through the quote request form. The quotation comes within 12 hours at the latest. The coil range shows the five coil types and their size limits.

Related coil guides: import steel coil from Türkiye; steel coil importers guide; steel coil HS codes; steel coil cost drivers.

Questions buyers ask

Does Reinwent publish a list of steel coil manufacturers in Türkiye?

No. We do not publish mill names. We put your specification to manufacturers that can meet it and send you the offers set out on one basis, so you judge each one on what it states in writing.

Is Reinwent a steel coil manufacturer?

Reinwent is a trading and sourcing company that sources coil from manufacturers in Türkiye. We collect offers, check that they answer your specification and follow the order from the quotation to delivery.

Which processing line does each coil type need?

Pickled and oiled hot rolled coil needs a pickling line, and cold rolled coil needs cold rolling and, for formable grades, annealing and temper rolling. Galvanized and Aluzinc coil need a continuous hot-dip coating line, and prepainted coil needs a coil coating line on a galvanized base.

Does one mill make all five coil types?

Not necessarily. The lines are separate, and a plant may run some and buy the base coil for the others. Ask each mill which operations it runs itself and which are done elsewhere, and what that means for the coil you order.

What should I ask a mill before ordering coil?

Ask which standard and grade it will supply, the thickness and width limits it can roll, the coating designation it can apply, the coil weight and inner diameter it can pack, and how the coil is protected for shipping. Ask for each answer in writing.

Can a mill slit coil to my width?

Slitting is done on a separate slitting line, either at the mill or at a service centre. Our coil pages quote slit widths from 20 to 1500 mm (0.787 to 59.06 in) within the thickness range of the coil. Name the width, tolerance and coil weight in the enquiry.

What does a trading and sourcing company add when buying coil?

It turns your requirement into one specification, asks several manufacturers to quote against it, sets the offers on one basis and manages the order through packing, loading and shipping. You deal with one contact instead of several mills.

How fast do I receive a quotation for coil?

Send the specification through the quote form and the quotation comes within 12 hours at the latest, with the offers put on one basis.

Sources

Request a quote

Tell us the specification you need and we will check it with manufacturers in Türkiye. We reply with a quotation within 12 hours.

Request a quote