Steel coil importers guide: what to specify

An import enquiry for steel coil should state the product, one named standard, the grade designation, thickness and width in millimetres, the coating designation where there is one, full-width or slit, coil inner diameter and maximum weight, packing, quantity and destination. With those fields filled in, offers from different mills can be compared line by line. Reinwent is a trading and sourcing company that sources coil from manufacturers in Türkiye.

Last updated

Key facts

  • A coil enquiry is complete when it names the product, one standard, the grade, thickness and width in mm, the coating, full-width or slit, coil weight and inner diameter, packing, quantity and destination.
  • Grade names belong to a standard: DX51D+Z is an EN 10346 designation, DC01 an EN 10130 one.
  • The coating number in EN 10346 designations such as Z275 is the nominal total coating mass of both surfaces in g/m².
  • Thickness and width are ordered in millimetres, and nominal thickness of coated coil includes the coating.
  • Offers can be compared only when every field above is the same in each of them.

What should an importer specify for steel coil?

Coil is bought by specification, not by name. “Galvanized coil” or “CRC” describes a family; the mill needs a defined product to quote against. The table lists the fields we ask importers to fill in, with the ranges from our product pages so you can see what is realistic before you write the line.

What an import enquiry for steel coil should state
Order fieldWhat to writeRange on our pages
ProductHot rolled pickled and oiled, cold rolled, galvanized, prepainted or AluzincFive coil types
StandardOne named standard, such as EN 10346, EN 10130, EN 10111 or ASTM A653/A653MPer product page
Grade designationThe grade name from that standardDD11 to DD14, DC01 to DC06, DX51D+Z to DX57D+Z, S220GD+Z to S550GD+Z
ThicknessNominal thickness in mm and the tolerance class0.20 to 5.00 mm (0.008 to 0.197 in) [0.008 to 0.197 in]
WidthNominal width in mm, full-width or slit600 to 1650 mm (23.62 to 64.96 in) [23.6 to 65.0 in] full width; slit from 20 mm (0.787 in) [0.8 in]
CoatingDesignation and mass in g/m², both sides together; paint system for prepainted coilZinc 50 to 600 g/m²; Aluzinc AZ100 to AZ185
Coil weight and IDMaximum weight, inner diameter, outer diameter limitUp to 30 t [66,100 lb]; ID 508 to 610 mm (20.00 to 24.02 in) [20 to 24 in]
Packing and logisticsPacking type, quantity in tonnes, destination port or site

Ranges depend on the coil type, the grade and the coating; prepainted coil is limited to 15 t per coil and Aluzinc to 2.00 mm (0.079 in) thick and 1250 mm (49.21 in) wide. Exact limits are confirmed at quotation.

How do you read a coil specification line?

A specification line packs several fields into one string. Take a galvanized example: EN 10346, DX51D+Z275, 1.00 × 1250 mm (49.21 in), coil ID 508 mm (20.00 in), maximum 8 t.

  • EN 10346 is the standard for continuously hot-dip coated steel flat products for cold forming.
  • DX51D is the grade name. The naming follows EN 10027: the letters describe the steel, and the D marks a product for cold forming.
  • +Z275 is the coating suffix: Z for zinc, and 275 as the nominal total coating mass of both surfaces, in g/m². The standard also sets minimum values, checked by test, so read the figure as a designation, not as a promised minimum.
  • 1.00 × 1250 mm (49.21 in) is nominal thickness times nominal width. For coated coil the nominal thickness includes the coating.
  • Coil ID and weight set how the coil sits on your uncoiler and what your crane or truck can take.

Cold rolled coil follows the same logic: EN 10130 names grades such as DC01, and the surface and finish are ordered separately. Our steel coil grades guide explains each prefix, and the coil standards guide shows which standard covers which product.

Slit coil or full-width coil?

Full-width coil keeps the width the mill rolled it at. Slit coil is cut lengthwise into narrower strips, which IspatGuru describes as a normal step for coiled flat steel. If your part is much narrower than the master coil, ask for slit coil and state the width, the tolerance and any edge or camber requirement. The trade-offs are set out in slit coil vs full-width coil. Size choices by application are in the coil thickness and width guide, and the coil weight calculator gives strip mass per metre from thickness and width at 7.85 g/cm³.

How do you compare coil offers on a like-for-like basis?

Before any commercial comparison, make the products identical. Put the offers in a table with one column per mill and one row per field:

  • the same standard and grade designation;
  • the same nominal thickness, width and tolerance class;
  • the same coating designation, or the same paint system and colour reference;
  • the same coil inner diameter and maximum coil weight;
  • the same packing, including how coils are strapped and protected;
  • the same quantity and the same delivery point.

If an offer leaves a field open, ask the mill to fill it in rather than assume it matches. The technical drivers behind differences between offers are covered in steel coil price factors, without any figures.

What mistakes do importers commonly make?

  1. Naming a grade without a standard. The same grade letters can appear in more than one system, and tolerances differ.
  2. Reading the coating figure as one side. In EN 10346 the Z or AZ number covers both surfaces together.
  3. Mixing EN and ASTM designations. G90 and Z275 are close in size but belong to different standards and are not converted here. Pick one system per order.
  4. Ordering by gauge. Gauge numbers differ between systems, so write millimetres.
  5. Leaving coil weight and ID open. The mill chooses its own, and it may not fit your line or your container.
  6. Ignoring packing. Packing affects handling and loading; see steel coil packing and container loading.
  7. Skipping the customs classification. Check it with your broker early; our guide to steel coil HS codes explains how width, rolling and coating steer the heading.

How does Reinwent work for coil importers?

Reinwent is a trading and sourcing company that sources coil from manufacturers in Türkiye, which worldsteel’s production table lists among the ten largest crude steel producers. You send one specification; we ask mills to quote against it, set the offers out on the same basis and follow the order through packing, loading and shipping. The steps are described in importing steel coil from Türkiye, and how to evaluate a steel coil manufacturer in Türkiye lists the questions we put to a mill. The steel coil hub shows the whole range: galvanized, cold rolled, pickled hot rolled, prepainted and Aluzinc coil. When the fields are ready, request a quote and the quotation comes within 12 hours at the latest.

Related coil guides: steel coil HS codes; importing steel coil from Türkiye; steel coil manufacturers in Türkiye; steel coil price factors.

Questions buyers ask

What is the minimum information an importer should send for a steel coil enquiry?

Send the coil type, the standard and grade designation, nominal thickness and width in millimetres, the coating designation if the coil is coated, full-width or slit, the inner diameter and maximum coil weight, the packing wanted, the quantity and the destination. Each missing field has to be guessed by the mill, and guesses differ between offers.

How do I read a line such as DX51D+Z275?

DX51D is the steel grade name under EN 10346 for hot-dip coated flat products for cold forming, and +Z275 is the coating: zinc, with a nominal total coating mass of 275 g/m² on both surfaces together. The coating number is a nominal figure for both sides, not one side.

Should the order name a standard or only a grade?

Name both. A grade name belongs to one standard, and the standard also fixes tolerances, testing and the order options. Choose one standard per order, such as EN 10346 or ASTM A653/A653M, and take the grade and coating designation from it.

What does G90 mean on a US specification?

G90 is an ASTM A653/A653M zinc coating designation. It corresponds to 0.90 oz/ft² of coating, both sides together, which is about 275 g/m². Write the ASTM designation in the enquiry if the buyer works to ASTM, and do not treat it as an EN designation.

How do I compare two offers for the same coil?

Check that both state the same standard, grade, nominal thickness with tolerance class, width, coating designation, coil weight, inner diameter, packing, quantity and delivery point. Only then compare the commercial terms. An offer with a field left open is not the same product as one with the field filled in.

Can Reinwent supply slit coil as well as full-width coil?

Yes. Our product pages list full-width coil from 600 mm (23.62 in) wide and slit coil from 20 mm (0.787 in) wide, within the thickness range of each coil type. The width plan, edge condition and coil weight are confirmed in the quotation.

Is Reinwent the mill that makes the coil?

No. Reinwent is a trading and sourcing company that sources coil from manufacturers in Türkiye. We ask mills for offers against your specification, set them out on one basis and follow the order through to delivery.

How fast do I get a quotation?

Send the specification through the quote form and the quotation comes within 12 hours at the latest.

Sources

Request a quote

Tell us the specification you need and we will check it with manufacturers in Türkiye. We reply with a quotation within 12 hours.

Request a quote