Key facts
- Galvalume, Zincalume and Aluzinc name the same type of product: steel strip coated with about 55% aluminium, 1.6% silicon and the balance zinc by the continuous hot-dip process.
- Galvalume and Zincalume are trade names of their owners. The standards use neutral wording: “55% aluminum-zinc alloy-coated” in ASTM A792 and “aluminium-zinc (AZ)” in EN 10346.
- In EN 10346 the designation is AZ plus the nominal total coating mass of both surfaces in g/m², for example AZ150 [0.49 oz/ft²]. The range offered here is AZ100 to AZ185.
- ASTM A792/A792M covers the product in coils and cut lengths for corrosion resistance, heat resistance, or both.
- Order by specification (coating type, AZ designation, thickness, width, standard), not by brand name.
Why are there three names for one coating?
The standards describe the product without any brand: ASTM A792 calls it 55% aluminum-zinc alloy-coated steel sheet and EN 10346 calls the coating aluminium-zinc (AZ). Galvalume and Zincalume are trade names of their owners, and Aluzinc is the name used for the coil sold here. The names are therefore labels, not different materials.
For a buyer this has one practical effect: a tender or a data sheet may say Galvalume, Zincalume or Aluzinc, and a supplier may be asked for any of them. Reinwent sells Aluzinc coil and mentions the other names only so that buyers can find it. This guide does not tie a name to a country, because the neutral sources read do not give a reliable map.
| Where you see it | Wording | What it means |
|---|---|---|
| Galvalume | Trade name | 55% aluminium-zinc coated steel |
| Zincalume | Trade name | The same type of coating |
| Aluzinc | Name used for the coil sold here | The same type of coating |
| EN 10346 | Aluminium-zinc coating, code AZ | Designation such as DX51D+AZ and AZ150 |
| ASTM A792/A792M | 55% aluminum-zinc alloy-coated steel sheet | Coating weight designation such as AZ50 [AZM150] |
What is the coating and how does it protect?
The coating has an aluminium-rich matrix with zinc-rich regions between the aluminium-rich dendrites, and a thin aluminium-iron layer bonds it to the steel. IspatGuru reports that the zinc-rich regions corrode preferentially, which gives the coating enough galvanic protection to limit rust staining at edges and other breaks in the coating. It also reports that in most environments the coating has been found to have 2 to 4 times the corrosion resistance of galvanized coatings. Treat that as a general finding: the real life depends on environment and coating mass.
The same source places its heat oxidation resistance between that of galvanized and aluminized coatings. This guide gives no temperature limit, since none was verified. Ask the mill for the limit of your application. For the full comparison with zinc, read galvanized vs Aluzinc coil.
How is it designated?
EN 10346 (compared with the other coil standards in steel coil standards: EN 10111, 10130, 10346) lists aluminium-zinc (AZ) among its coating types, and grades are written with a suffix, such as DX51D+AZ. The number after AZ is the nominal total coating mass of both surfaces in g/m². AZ100 is 100 g/m² [0.33 oz/ft²], AZ150 is 150 g/m² [0.49 oz/ft²] and AZ185 is 185 g/m² [0.61 oz/ft²]; US values use 1.00 oz/ft² = 305 g/m².
ASTM A792/A792M covers the product in coils and cut lengths. It states coating weight in oz/ft² (A792) or g/m² (A792M), and says the two systems are not necessarily equivalent. AZ50, also written AZM150, is 0.50 oz/ft². Do not mix the two systems on one order. The mass ranges also differ in how they are offered, so confirm the designation against the mill’s range.
Where is it used?
Typical uses of Aluzinc coil are roll-formed building products such as roofing and cladding, parts that need heat resistance, and the base for prepainted steel coil, whose paint systems are covered in prepainted coil paints and RAL colours. IspatGuru names pre-engineered metal buildings, especially roofing, as the main application, with appliances and automotive parts also listed. The coating can be painted on the coil line or after fabrication.
How do you specify it in an enquiry?
State these items together: coating type (55% aluminium-zinc), designation (for example AZ150), grade or standard (EN 10346 or ASTM A792), thickness and width in mm [in], full-width or slit coil, coil weight and inner diameter, quantity, end use and destination. The range sourced is 0.25 to 2.00 mm (0.010 to 0.079 in) [0.010 to 0.079 in] thick and 600 to 1250 mm (23.62 to 49.21 in) [23.6 to 49.2 in] wide. Estimate coil weights with the steel coil weight calculator and send everything through the quote form. Reinwent is a trading and sourcing company, and the coil comes from manufacturers in Türkiye. For shipping, read steel coil packing and container loading. The steel coil page shows the rest of the range.
Read next: what is galvanized steel, galvanized vs stainless steel.

Steel


